Family tradition. Quality for a lifetime.

MENU

Mark Sirianni Watch Repair
25 Fraley St.
Kane, PA. 16735
814-837-9435
814-558-4818 (cell)
watchdoctorpa@gmail.com

Watch Repair Basics

[Pocket Watch Dials] [Watch Jewels] [Escapement][Care of your Vintage Watch]

Adjustment

Movements that are marked to be "Adjusted" may have a variety, or combination, of features. One has to read the catalog description for any given movement grade to discover just what level of adjustment is being claimed. High grade watches built after 1905-1908 may be marked with specific adjustments. This is especially true for watches intended for use in railroad time service. The balance (wheel), the wheel that spins back and forth rapidly is the device that sets the timekeeping rate of the watch. The purpose of all of the features for an adjusted watch is to keep the balance (wheel), as nearly as possible, oscillating at a consistent rate. The consistency of the rate of oscillation of the balance (wheel) thus determines the timekeeping quality of the watch.

Temperature Compensated Balance (wheel)

A balance (wheel) that is temperature compensated has the rim made of two dissimilar metals. There are usually two arms (spokes) from the hub supporting the rim and there is a slot cut in the rim just past each arm. This forms two rim segments having one end supported by the arm and the far end free to move. These slots, and the two colors of metal in the rim, are identifying characteristics. As the temperature increases, lessening the power of the hairspring - the spring coiled inside of the balance (wheel) - the far ends of the rim segments deflect inward. As temperature decreases, the segment ends relax, moving outward, as the hairspring strength increases. The action is much like an inexpensive thermostat in the home. This movement of the rim segments changes the moment of inertia of the balance (wheel), compensating for the alteration in the hairspring strength.

Adjustment to Temperature

This is sometimes referred to as adjustment to heat and cold. It requires a temperature compensated balance. The balance has pairs of screws (180 degrees apart) set into the rim. These give the balance mass, which sets the basic rate at which it oscillates. One pair may be the meantime screws (which can be identified - if present - by being longer than the other screws), used to bring the rate deviation to minimum (with the regulatorin its center position) after all of the other adjustments have been made. The locations of most of the pairs of screws (each pair is 180 degrees apart) on the balance (wheel) rim are chosen to provide the best match of change in moment of inertia to change in hairspring strength (there are extra pairs of holes so that the screws may be moved to the best possible positions). The object is to keep the balance (wheel) oscillating at the same rate over the specified temperature range.

Adjustment to Position

The next level is adjustment to position. This is adjustment to maintain the same rate of balance (wheel) oscillation, regardless of which of the specified positions the watch is in. There are a total of six positions. Unfortunately, the number or the positions to which the watch is adjusted isn't specified for most watches built prior to 1905-1908. Typically, unspecified adjustment to position means adjustment to three positions, but there are a number of instances in which it means five, or sometimes 6, positions. Adjustment to three positions most likely means stem up, stem at the 3 o'clock position and stem at the 9 o'clock position.

 

In discussing adjustment to positions (on the NAWCC Pocket Watch Message Board, 26-Aug-06), John Runciman, quoting from the book Watch and Clock Information Please W. H. Samelius? by O. R. Hagans, posted a definition of adjustment to four positions as dial up, stem up, stem at the 3 o'clock position and stem at the 9 o'clock position. It was also stated in O. R. Hagans' book that adjustment to two positions was defined as dial up and stem up, while adjustment to one position was stem up with watch inclined 45 degrees to the rear The marking "Adjusted 2 Positions" is only occasionally seen, seemingly only on low grade Swiss watches. An indication of adjustment to one position is almost never seen.

 

Watches adjusted to five positions include the three positions of stem up, stem at the 3 o'clock position and stem at the 9 o'clock position, plus the dial up and dial down positions. Robert Sweet once posted several pages from the 1914 edition of the Hamilton Timekeeper which lists the five positions in order as (1) dial up, (2) dial down, (3) stem up, (4) stem at 9 o'clock and (5) stem at 3 o'clock. The 6th position is stem down at the 6 o'clock position. These positions are illustrated in a 1924 Illinois ad'. Since temperature variation is usually greater than positional variation, watches marked to be adjusted to position include adjustment to temperature. A high grade Swiss watch marked to be adjusted usually implies adjustment to all positions, wherein "all" may be 5 or 6 positions. Nevertheless, it takes a bit of experience to distinguish those movements to which this applies.

 

Some watches are marked ?8 Adjustments.? Depending upon the manufacturer?s specification at the moment that the watch was made, this can mean adjustment to temperature, isochronism (see below) and 6 positions. Or,it may mean adjustment to heat, cold, isochronism and 5 positions. To clear up the ambiguity, in the early 1950?s, Elgin marked its top (and only) railroad pocket watch ?9 Adjustments.?

 

Dave Chaplain reported the following Tariff Act of 1930 Discussion of Adjustment, on the NAWCC American Pocket Watch Message Board on September 18, 2008, 09:59 PM.

 

"The Tariff Act of 1930 has fees associated with watches of varying adjustments with a possibility of 9 total adjustments as follows:

 

"6 adjustments to position: stem up, stem left, stem right, dial up, dial down, stem down - another government publication of 1946 refers to these 6 positions and states that most "high quality watches" are adjusted to 5 positions and omitting the stem down adjustment, and "good quality watches" with 3 position adjustments most often are the stem up, dial up and dial down postions

 

"2 adjustments to temperature: hot and cold - the 1946 paper describes "modern monometallic solid balances" ... "with hairspring made of Elinvar or some similar nickel steel alloy" as making these temperature adjustments moot

 

"1 adjustment to isochronism"

 

Another point on the subject of adjusting was posted by Don Dahlberg, pointing out that the rate to which watches were adjusted varied from grade to grade.

 

The marking "Adjusted" on a movement means whatever the manufacturer said it meant at the time that the watch was built. Lacking descriptive factory literature, we have no way of knowing what that means today. Unless a watch is specifically marked as to the number of positions to which it is adjusted, such as a watch that is only marked "Adjusted," the only way to know that number (if it is adjusted to positions at all) would be to identify the grade and find the manufacturer's description of the position adjustment for that grade. For example, the U.S. Watch Co. of Waltham's "The President" grade is only marked "Adjusted" (in the 9 o'clock position - right at the junction of the two damaskeened circles), yet U.S. at Waltham's descriptionstates that it is "adjusted to heat, cold, isochronism and all positions, ..." Another example is Waltham's grade No. 35, which is only marked "Adjusted." The descriptionof that grade is "Adjusted to Heat and Cold, and in all Six Positions." A lesser example is the model 92 Appleton, Tracy & Co., which simply marked "Adjusted." A February 1902 Waltham addescribes it to be only adjusted to three positions. When the Appleton, Tracy & Co. Premier grade was introduced a few months later, it too was only marked "Adjusted," but anOctober 1902 Waltham adstates that it was adjusted to five positions.

Adjustment to Isochronism

Then, there is adjustment to isochronism. This is accomplished by the design and adjustment of the hairspring - the spring coiled inside of the balance (wheel). The power output of the mainspring (the spring that is wound when winding a watch) tends to decrease as it unwinds over the course of the day. This causes the balance (wheel) to rotate through a greater rotational angle when the mainspring is just wound and a lesser angle when the mainspring needs winding. A watch adjusted to isochronism oscillates the balance (wheel) at the same rate throughout the specified length of run between windings of the mainspring, regardless of how far in each direction the balance (wheel) rotates. This length of run is typically 30 hours for earlier watches and 42 hours for post World War I watches of better quality. However, mainsprings whose power output were nearly constant over the first 20 hours after a full winding were supplied in higher grade watches starting in the late 1920's. The need for adjustment to isochronism lessened with the application of these mainsprings.

 

 

 

I will be happy to answer any questions that you have about the repair of your watch.I can also take a look at an ebay auction that you are thinking of bidding on.

Glad to help in any way that I can     Email -  watchdoctorpa@gmail.com

 

 

 

 

 

 

 

 

 

 

 

is always in

 

 

 

 

 

  • Follow me on:
  • Watch Doctor on Facebook
  • Watch Doctor on Twitter
  • Watch Doctor on LinkedIn
  • Check Out My Ebay Feedback



  • Proud Member:
Kane Chamber of Commerce
54 Fraley Street
Kane, PA 16735
814-837-6565
PA Jewelers Association